Miracle Shield is a revolutionary coating that adds luster without the use of silicones or waxes. Miracle Shield dries crystal clear without any buffing, and protects without leaving a greasy or oily feel like the other nationally advertised "protective coatings". With this long lasting advantage you'll have more savings for important matters and leisure activities!

Cleans, protects and beautifies: vinyl, leather, wood, plastics, carpets, chairs, autos, trucks, TV's, boats, rubber, and most painted surfaces.

It even protects against mildew growth, and wear on virtually all non-cloth surfaces.

It's guaranteed never to chip, crack or peel and will never yellow. It is non-flammable and non-toxic and contains no harmful oils or waxes.

Surfaces
Use Miracle Shield on the following surfaces:

Vinyl	Roof's
Plastic	Concrete
Rubber	Asphalt
Metal	Stone Work
Interior Wood	Brick Work

NOTE: Outdoor applications should be a minimum of two coats solution.

Finish- Miracle Shield will dry to a satin or low-luster semi-gloss finish. Which is scratch resistant. There is no buffing required.

Application
Miracle Shield can be applied as follows:

• Brush it on
• Spray it on
• Roll it on with a short nap roller
• Wipe it on
• Sponge it on

Miracle Shield hardens best at a surface temperature of 55 degrees or higher on an average of 15-20 minutes.

Surface Preparation- In order for Miracle Shield to work properly, the surface must be free from any dust, dirt grease, grime or wax. You can remove any oil, wax or grease with household rubbing alcohol.

Elastomeric Clear Sealer, Finish
Miracle Shield is a Clear Acrylic Elastomeric Sealant designed to seal and protect a wide range of surfaces including wood homes, stone, brick, masonry and concrete, roofing materials and reflective roof coatings.

All white roof coatings start losing their reflectivity properties due to accumulated dirt and other contaminates. Until now clear protective coatings for elastomeric base coatings were not available due to their lack of flexibility which is necessary as roof coatings are designed to expand and contract with a roofs movement.

Miracle Shield also features outstanding adhesion to the applied surface, elongation and recovery capabilities, a combination of UV absorbers and mildewcides enabling it to resist the effects of the most severe climatic conditions.  Now all roof coatings can be protected from surface contamination enabling them to perform as intended by reflecting radiant heat away from the buildings interior.

This self cleaning clear coat works much the same way as the clear coatings designed and used on automobile finishes.

Miracle Shield is truly an all-purpose clear sealant and protectant, suitable for virtually any application.

• Color: Milky White, dries clear.
• Volume Solids: 41% +/- 2%
• Flash Point: Same as water.
• Coverage: 350-400 sq. ft. per gallon depending on the porosity of the surface.

Recommended Coverage: The number of coats depends on surface porosity; however, one coat is all that is normally needed on a well sealed surface.

Drying Time: Will depend on climate conditions. Allow at least 2 hours drying time between coats. First coat must be thoroughly dry before applying second coat.

Limitations: Not suitable for below grade use.

Surface Preparation Surface must be clean and free from dirt, dust, grease, oil, mildew, wax, loose paint.

Application: This product may be easily applied with a quality brush, short nap roller or airless spray equipment.  Surface must be clean, dry and sound. Surface must be free of grease, oil wax, mildew or any other surface contaminant. Surface and ambient temperatures should be between 45 and 90 F. Avoid application if rain or condensation could wet surface less than 1 hour after application. Allow 2 hour between coats for best results.

If applying by brush, apply a smooth, generous coat in small areas or cut in large areas first. If applying by roller, apply in even, generous strokes in an "M" or criss-cross pattern avoiding excessive respeading or reworking. Always maintain a wet edge by brushing or rolling into the previously applied area.

If applying by airless spray equipment, it is recommended to use a unit with a minimum of 2,000 psi pressure, with a 0.013 to 0.021 fluid spray tip.  During application, product should be back-rolled to insure proper adhesion and even dispersion.  Thinning should not be necessary but use a maximum of 1/2 pint per gallon if it is. Clean up equipment and any spills immediately with warm soapy water and thoroughly rinse with clean water.

Clean-up: Cleanup immediately after use with soap and water.

Miracle Shield FAQs

Question: What kinds of surfaces can Miracle Shield be used on ?

Answer: Wood, Concrete, Plastic, Vinyl, Rubber, Roofing materials... just about anything.

Question: What does Miracle Shield do ?

Answer: For Miracle Shield a clear, flexible barrier film. Never slippery or oily. Easy application - just apply & let dry. Will not crack or peel. Protects against Ultra-Violet damage with no silicones or waxes. Works on most non-cloth surfaces. Treated surface cleans up with soap and water.

Question: What color is it ?

Answer: Miracle Shield goes on as a slightly milky, translucent liquid. It dries clear. Tinting has not been tested. Try a small sample first.

Question: What kind of coverage can I expect ?

Answer: You can figure that the average spread rate is 300 to 500 sqft/gal and highly dependent upon the porosity of the surface. Concrete pool deck about 300, Cedar yard fencing 400, Stucco wall 250, Old asbestos shingles 300, Wood patio deck 500, Public restroom dividers 600+ when diluted.

Question: How should it be applied ?

Answer: It can be rolled, brushed or sprayed. In vertical applications, it can even be wiped on with a damp cloth.

Question: What is the life time of the coating ?

Answer: High traffic areas should have 2 or more coats applied and life will vary from 2 to 5 years. Vertical applications will last for the lifetime of the surface. A typical roofing application will extend the life of the roof another 10 years.

Question: Is the surface slippery ?

Answer: NO. Miracle Shield will have a slight elastic "give" to it's surface which should give a superior non-slip characteristic.

Question: Can I spray Miracle Shield over Therma Guard paint ?

Answer: YES ! These products work exceptionally well together. Ideal applications include a roof or external walls where you can mate the radiant reflection and insulating properties of TG with the sealing elastic properties of the Miracle Shield.

Question: Can I mix TG Cells with Miracle Shield and get protection and insulation simultaneously ?

Answer:  YES ! TG Cells (packaged dry ceramic spheres) are a new product in the Therma Guard line. Industrial users mix these products with great results and gain the benefits of both products with one application. This is very popular in roof repair applications.

Question: Does Miracle Shield contain harmful chemicals ?

Answer: NO. Miracle Shield is free of all Volatile chemicals and toxins and is recognized as safe, under the Federal Food, Drug, and Cosmetic Act. Non-toxic, odor free and environmentally friendly.

Question: Can Miracle Shield be diluted ?

Answer: YES. It just forMiracle Shield a thinner protective coating

Question: Is there a craft application for Miracle Shield ?

Answer: YES! Absolutely! Paintings, ceramics, wood working projects, jewelry ect. Anything where water proofing, UV and mildew protection would be a benefit. Try it a test surface first to insure a desired result.

Miracle Shield MSDS